Atlas Accessories
Added flexibility for mounting and positioning cymbals and percussion accessories around the drum set.



Share

The A.T.L.A.S. Mount (LAPAM1)

The World's Only Integrated Lug Suspension System and Mounting Bracket (Pat.Pend)

Create a suspended mounting location anywhere
on your drum by simply replacing a lug!

(Click to view)




Product Info

Product Info

The A.T.L.A.S. (or Aerial Tom Lug Attached Suspension) Mount creates a mounting location anywhere on a drum, NO DRILLING REQUIRED. It simply attaches to the shell by replacing a lug (fits 25mm to 43mm holes spacing- including Ludwig Small & Large Classic, and Keystone Lugs).




Suspension and Isolation

Suspension and Isolation

(click any kit photo to view a larger image)
The Suspension is IN the Mount

The Suspension is IN the Mount
The 12.7mm clamp on the A.T.L.A.S. Mount is isolated from shell contact by two hardened steel pins, floating on elastomer mounts over the integrated tension lug.
The Proof is in the Sound!

The Proof is in the Sound!
Unlike traditional isolation systems that mount the drum around the tension rods, the A.T.L.A.S. mount effectively separates the isolation system from the drum; allowing the drum to resonate as an independent unit. The result is a smoother decay, longer sustain, and increased resonance. The sustain plots (shown here) clearly show the effect.
Increased Set-Up Flexibility

Increased Set-Up Flexibility
Auxiliary cymbal arms, accessories, and floor tom legs are positioned with ease and totally isolated from the shell. Enlarge your set-up by integrating the A.T.L.A.S. mount with additional Atlas Tom and Cymbal holders.

Installation Tips

Installing your A.T.L.A.S. Mount

  • Based on where the existing lugs are mounted, select the drum's best mounting point (for toms, we recommend the top row on either side of the badge.)
  • Remove the drum head, rims and selected lug from the drum.
  • Position the A.T.L.A.S. Mount with the tension rod insert facing toward the bearing edge. Fit the bottom of the A.T.L.A.S. mount using the thicker of the two sets of included gaskets, adjusting the mounting bolt spacing to fit the existing lug holes. (for toms, use the thin gasket; for bass drums, use the thick gasket.) For Tom mounting, locate the A.T.L.A.S. mount in one of batter head lug positions.
  • Insert the edge of the top attachment bolt into the top lug hole in the shell. Align the bottom attachment bolt to be inserted into the bottom lug hole.
  • Attach A.T.L.A.S. Mount onto the shell with both attachment bolts through the lug holes. Put the washers on both attachment bolts and secure each 10mm nut to each bolt with no spacing or slack on the inner shell (Tighten bolts until you can not shift the base of the mount by hand. DO NOT OVERTIGHTEN)
  • Resecure the drum head on the shell and tune as normal.
  • Secure the included Memory Lock onto the intended 12.7mm mounting rod and position to proper angle. The ATLAS Mount is engineered to fit snug to the Memory Lock at both top and bottom locations, so be sure to position it where it will most effectively allow for angle and height position.

Gallery

Gallery

(click any kit photo to view a larger image)

Other Atlas Accessories

To get the most out of you're A.T.L.A.S. Mount, we recommend:

Cymbal Mounting Arm with Aerodyne Tilter (LAC251CH)

Cymbal Mounting Arm with Aerodyne Tilter (LAC251CH)
12.7mm Accessory Rods

12.7mm Accessory Rods
Pro Double Tom Accessory Clamp (LAP256STH)

Pro Double Tom Accessory Clamp (LAP256STH)
gray line

lineline
Copyright © 2012 Conn-Selmer, Inc. All Rights Reserved.         Privacy Policy | Terms of Service